新浪微博 腾讯微博 在线留言 收藏本站 网站地图

您好,欢迎来到鑫广大官网!

佛山市新广大自动门窗工程有限公司

工业门厂家直销——鑫广大工业门、快速门、铝合金卷门等生产制造商

咨询热线:13826276153

鑫广大十年专注于高端工业门研发生产
当前位置:首页 » 鑫广大资讯 » 工业门厂家新闻 » 工业门讲解车库门的常见故障及排除方法

工业门讲解车库门的常见故障及排除方法

文章出处:责任编辑:查看手机网址
扫一扫!工业门讲解车库门的常见故障及排除方法扫一扫!
人气:-发表时间:2016-01-24 13:50【

1.电机运转不正常,有连续嗡嗡声。主要是因为二相运行,唯一的办法就是先检查动力回路接通三相。
      The 1 motor operation is not normal, continuous hum. Mainly because of two phase operation, the only way is to check the power circuit connected to three-phase.
    2.阀门卡死,导致的原因可能是反向旋转和限位开关调整得不正确,解决方法是在阀门开启位置时,使用手轮操作中的锤击机构能打开卡死的阀门。
      The 2 valve stuck, can result from reverse rotation and limit switch not adjusted right, the solution is in the valve open position, click mechanism can open the death card using the handwheel operation of the valve hammer.
    3.执行机构旋转,但没有驱动阀门。导致原因离合器杆挂锁在“手动”位置和动轴套位子没有对好。解决方法有离合器打到“远操”和对好轴套位置。
      3 actuator rotation, but not to drive the valve. Causes the clutch lever padlock in the "manual" position and the movable shaft sleeve seat is not good. The solutions of clutch hitting "remote operation" and good shaft position.
    4.阀门没有到位电机就停止运转。导致原因行程控制器调整不良,转矩控制器提前动作。
       The 4 valve did not reach the designated position motor stops running. The cause of stroke controller adjust the bad, torque controller early action.
    5.转矩、行程开关不起作用失控。导致根源相序接错、线路接错、接触器吸铁不释放。解决方法是调换电机相序、检查线路纠正错误、清洁或调换接触器。
      The 5 torque and stroke switch does not work out. Root cause of phase sequence connection fault, fault line access, contactor iron absorption does not release. The solution is to replace the motor phase, check line to correct the error, clean or replace the contactor.
车库门使用注意
Garage door use note
很多时候广大消费者没有注意日常使用的安全,以为车库门的安全性很高,并不会发生什么意外,出于安全着想,大家使用车库门注意事项
     When a lot of consumers did not pay attention to safe for daily use, the safety that garage door is very high, and will not happen any accident, for the sake of safety, we use the garage door note
1)收到遥控器及钥匙后请安装人员演示遥控器及手动钥匙开关门。
1) received from the remote controller and key please installation personnel demonstration of remote control and manual key switch door.
2)安装完成后务必请安装人员对门体进行调试运行,运行顺畅后方可交接遥控器及钥匙,保修卡。
   2) after the completion of the installation must install personnel door body debugging and running, running smoothly before handing over the remote controller and key, warranty card.
3) 禁止在看不到门体运行情况的地方操作遥控器,以免造成安全事故或车库门误开。
3) is forbidden in the local remote control operation can not see the door body running conditions, so as to avoid safety accident or garage door opened by mistake.
4)门体正在运行时,严禁人或物体从门体下方通过,或在门体下方停留。
    the door body is running, it is strictly prohibited to people or objects through from the door body below, or stay under the door body.